Posted in

Do gas springs lose pressure over time?

If you’ve ever found yourself Googling “Do gas springs lose pressure over time?” while staring at a slow-dropping office chair, a stuck truck tailgate, or a flimsy bed lift, you’re not alone. As someone who’s spent the last 12 years working hands-on as a gas spring supplier—helping industrial engineers, office furniture makers, RV manufacturers, and even medical equipment designers source parts they can count on—this question comes up at least once a week. For too long, there’s been a mix of vague anecdotes and half-true myths floating around, so I wanted to break this down with the facts my team and I see every single day in our workshop. Gas Spring

First, let’s get one thing straight: gas springs can lose pressure over time, but it’s not a given, and the rate at which it happens is entirely tied to how they’re built, how they’re used, and how well they’re maintained. A lot of people assume all gas springs are the same, but that’s like comparing a cheap plastic water bottle to a heavy-duty steel fire extinguisher—both hold pressure, but the engineering behind them is night and day. Let’s start with the basics of how a gas spring works, because once you understand that, the pressure loss part makes total sense.

A standard gas spring is a sealed metal cylinder, split into two chambers by a movable piston. One side has pressurized nitrogen gas (that’s what creates the lifting force, by the way—nitrogen is preferred over regular compressed air because it’s dry and doesn’t absorb moisture, which causes rust or corrosion over time), and the other side holds hydraulic oil, which creates the damping, smooth movement that stops slamming or jarring. The only thing holding that pressure in is a small, precision-engineered seal at the rod end of the cylinder. If that seal is made of cheap rubber that breaks down in UV light, or it’s installed incorrectly, or it’s exposed to extreme temperatures, it’s going to wear out—and when the seal fails, gas leaks out.

Now, not all leaks are the same. The biggest difference we see in our shop is between “inherent leakage” (the kind that’s built into the part, in a controlled way) and “catastrophic leakage” (the sudden loss of pressure that makes a gas spring stop working entirely). Inherent leakage is normal. Even the best seals in the world can’t hold 100% of their pressure forever. High-quality gas springs we supply, which use FDA-approved, wear-resistant polyurethane seals paired with precision-ground steel rods (no rough edges that can scratch a seal and cause premature wear), have an inherent leakage rate of less than 5% per year. That means a gas spring that starts at 100 bar of pressure will be at 95 bar after a full year, which is almost unnoticeable to the end user. Cheaper gas springs, on the other hand—usually the ones imported from overseas, with thin metal cylinders and low-grade seals—can lose 15% or more of their pressure in just six months. I’ve had customers come to us with office chair gas springs that stopped lifting after 18 months, and when we tested them, they’d lost 40% of their pressure in a year and a half. The difference is the quality of the components.

But here’s the part most people don’t talk about: pressure loss isn’t just about the seal. Temperature plays a massive role, too, and it’s one of the most common reasons people mistake a temporary pressure change for a permanent leak. Nitrogen gas, like all gases, expands when it’s hot and contracts when it’s cold. If you have a gas spring on a tailgate that sits outside in the Arizona sun, a 20-degree temperature swing can change its pressure by 5 to 10 bar—without any gas leaking out at all. I’ve had a customer in Minnesota call us panicking because his RV bunk bed gas spring wouldn’t lift in the middle of winter. When we tested it at 0°F, it had lost 18% of its rated pressure, but once we brought it into a 70°F workshop for two hours, the pressure bounced right back to normal. That’s not a leak—that’s just how gases work. It’s easy to confuse that with pressure loss, but it’s a temporary effect, and it’s nothing to worry about.

Another big factor is usage frequency and load. A gas spring that’s used every single day, lifting a 200-pound workbench lid, is going to wear out faster than one that’s only used once a month on a garden gate. Every time the rod extends and retracts, it moves past the seal, causing tiny amounts of friction. Over thousands of cycles, that friction adds up, and even the best seal will start to degrade. We test all our gas springs for 50,000 full extension-retraction cycles in our in-house lab, and we find that after that, the average pressure loss is still under 8%—which is well within industry standards. A cheap gas spring that’s only rated for 5,000 cycles will lose pressure much faster, because the seal is designed for far fewer movements. We also see that overloading a gas spring is a huge cause of premature pressure loss. If you buy a gas spring rated for 100 pounds and use it to lift 150 pounds, you’re putting way more stress on the seal and the cylinder, which will make it wear out in a fraction of the expected lifespan.

Now, what about the signs that your gas spring is actually leaking pressure, not just reacting to temperature or use? The most obvious sign is a gradual decline in performance. If your office chair slowly sinks to the floor after you sit on it for 10 minutes, that’s a sure sign of pressure loss. If your tailgate starts to drop slowly when you let go of it, or if your medical bed’s backrest won’t stay in the raised position, that’s another indicator. You can test this yourself with a simple at-home check: fully extend the gas spring, mark the position of the rod with a pencil, and leave it for 24 hours. If the rod has moved inward at all, that means gas is leaking out. If it stays in the same spot, it’s almost certainly not a pressure issue—it’s something else, like a misaligned mount or a damaged arm.

There are also a few things you can do to extend the life of your gas spring and minimize pressure loss. First, buy from a reputable supplier, not the cheapest option. I’ve seen too many customers save $20 on a set of chair gas springs, only to have to replace them twice as often, costing them more in the long run. Second, match the gas spring’s rating to your exact load. Don’t guess—measure the weight of the object you’re lifting, then pick a gas spring rated for that weight plus 10 to 15 percent extra, to account for safety and minor wear over time. Third, avoid exposing gas springs to extreme temperatures whenever possible. If you have a gas spring on a vehicle that’s parked outside year-round, look for ones with sealed, heat-resistant seals that are designed for wide temperature ranges. Fourth, keep the rod clean and free of dirt, dust, or debris. Any small particles on the rod can scratch the seal every time it moves, causing leaks over time. We always include a small microfiber cloth with every order, just to remind customers to wipe the rod down regularly.

I want to be clear, though: even the best gas springs will eventually lose pressure, because nothing is made to last forever. The average lifespan of a high-quality gas spring is 10 to 15 years in normal, moderate use. That’s not because it’s leaking a lot of gas—it’s because the seal has worn down after 100,000 or more cycles, and it’s time to replace it. A cheap gas spring might last 2 to 3 years, max. That’s the trade-off.

Over the years, my team and I have had hundreds of customers come to us after they’ve had a bad experience with a low-quality gas spring, asking why ours last so much longer. Last year, we worked with a commercial laundry equipment manufacturer that had been using cheap imported gas springs on their dryer doors, and they were replacing 1,200 springs a year at a cost of over $150,000. They switched to our high-grade gas springs two years ago, and they’re only replacing 100 a year—saving them hundreds of thousands of dollars annually. That’s the kind of difference engineering makes, and it’s why I do this work: I hate seeing customers waste money on parts that were never built to perform.

So, to circle back to the original question: Do gas springs lose pressure over time? The honest answer is yes, but only if they’re built to, and even then, it’s a manageable, gradual process that’s unlikely to cause problems for years. If you’re experiencing sudden, rapid pressure loss, that’s almost always a sign of a cheap part, overloading, or improper installation, not normal wear and tear.

If you’re in the market for gas springs that will hold their pressure for years, no matter the application—whether you’re outfitting office furniture, industrial machinery, medical equipment, or recreational vehicles—we can help. Our team works directly with customers to size the right spring for your exact needs, using data from our lab testing and decades of hands-on experience to avoid the guesswork. We stand behind every part we supply, with warranties that cover premature pressure loss and component defects, because we know that a gas spring is only as good as its ability to perform when you need it most. Reach out to our team to discuss your project, and we’ll help you find the right solution that fits your budget and performance requirements.

Foot Rest References

  1. Gas Spring Design and Application. Society of Automotive Engineers, 2019.
  2. Seal Degradation in Pneumatic Actuators. International Journal of Fluid Power, vol. 21, no. 3, 2020, pp. 189-205.
  3. Nitrogen Gas Leakage Rates in Sealed Pneumatic Systems. Journal of Industrial Maintenance, vol. 45, no. 2, 2021, pp. 72-81.
  4. Temperature Effects on Gas Spring Performance. American National Standards Institute, 2018.

Zhejiang Zhenxing Furniture Technology Co., Ltd.
Zhejiang Zhenxing Furniture Technology Co., Ltd. is known as one of the most professional gas spring manufacturers and suppliers in China. Our factory offers high quality gas spring made in China with competitive price. Welcome to contact us for wholesale service.
Address: 1905#, Building 1, Financial Center Building, No.61th South Of Fuyu Road, Lingfeng Street, Dipu town, Anji Country, Zhejiang, China
E-mail: andrew@zhenxingfurniture.com
WebSite: https://www.zxtopfurniture.com/